Trouble-shooting Hard Drive Problems - Part 1

It is extremely important not to make or write any changes to data on the hard drive without first verifying the hard drive configuration. Therefore, the first priority when unable to access information on a hard drive is to verify all of the configuration information dealing with the suspect hard drive.

Partition Parameter
Value or Equation

Partition Status
Bootable

Starting Head
1

Starting Sector
1

Starting Cylinder
0

Partition Type
Bigdos (drives greater than 30 MB), otherwise DOS 12

Ending Head
Total Number of Heads -1

Ending Sector
Sectors per Track displayed in Volume Boot Sector

Ending Cylinder
Number of Cylinders set in CMOS - 2

Total # of Sectors
Number of Sectors displayed in Volume Boot Sector

Start Absolute Sector
Number of Sectors per Track in Volume Boot Sector

Boot Signature
55AA

Step One: Make sure that Micro-Scope detects the hard drive

In Micro-Scope, System Configuration, Compare Settings - check to make sure that there is not an asterisk beside the number of hard drives detected value. If there is an asterisk, either the CMOS is set incorrectly, or there is an electronic problem (controller, cable, drive).

Step Two: Compare the BIOS parameters against the drive partition information.

In Micro-Scope, System Configuration, System Information - note the information displayed for the hard drive, specifically the parameters for the drive in question. Compare these parameters to the parameters in the MBR display under Micro-Scope, System Configuration, Partition Display using the following formula:

System Information
Master Boot Record

Cylinders
Ending Cylinder + 2

Heads
Ending Head + 1

Sectors
Sectors Per Track

If the information does not match, either the partition information is corrupt, or the CMOS setup or controller BIOS setup (if one exists) is incorrect, or there is a problem communicating with the drive.

Step Three: Check the drive functionality

In Micro-Scope, Diagnostics, Fixed Disk Tests - check the information in the Fixed Disk Selected window. Make sure that the proper drive type, model, and native parameters are showing in this window. If any of the information is incorrect, there is an electronic problem. Check the cable, controller and drive, re-seating all connections, and repeat the above procedure. After correcting the electronic problem, perform a read test on the first 10 cylinders of the drive. If any errors occur, then this is the most likely cause of the drive failure. Perform a read of the entire drive to determine if the errors are electronic in nature, or physical in nature. Electronic problems will result in the errors displayed not always being the same type or in the same location on the drive. If the problem is electronic, replace the cable, controller, and finally drive electronics and repeat the read test until no errors occur. If the error is physical, use an INT 13 type editor (such as Norton Advanced Editor), to block the entire drive and write the information to a daisy chained drive set to the same parameters as the faulty drive.

The next step, after the drive passes the read test on the first 10 cylinders, is to check the original partition setup of the drive.

Step Four: Check for the physical location of the master boot sector and the volume boot sector.

In Micro-Scope, Utilities, Fixed Disk Editor - use the FIND feature to search the last two bytes of each cylinder for a boot signature (55 AA). The first location where a boot signature should be found would be at cylinder 0, head 0, sector 1 (the master boot sector). The second location where a boot signature should be found is at cylinder 0, head 1, sector 1 (the volume boot sector). It is also possible to use the FIND feature to locate the volume boot sector by searching for MSDOS (in DOS based systems) or MSWIN (in Windows95 systems).

If there is a duplicate copy of the master boot sector found before the location of the volume boot sector, then it is possible that a boot virus has infected the hard drive in the system. The Rebuild Master Boot feature of Micro-Scope will eliminate any boot sector virus. Be sure to boot the system to the Micro-Scope diskette and immediately do a cold reboot of the system after using the Rebuild Master Boot feature.

If the volume boot sector is found in a location other than cylinder 0, head 1, sector 1, count the actual number of sectors before the volume boot sector, and compare that value to the value for the sectors per track displayed in the partition table described in step 2. If the values match, the most likely cause of the system failure is an incorrect CMOS setup. In this case the CMOS needs to be reset to the values indicated by the partition table described in step 2, remembering to use the formula described in step 2 when doing so. If the values do not match, set the CMOS Sectors Per track to the number of sectors counted before the volume boot sector and continue to the next step.

Step Five: Check the partition tables to make sure they are correct

Reboot the system to Micro-Scope and go to System Configuration, Partition Tables. Check the information displayed in the master boot record to see if there is any obvious corruption (that is, excessively large numbers, all partitions non-bootable, etc.) If there is no obvious corruption in the master boot record, then perform step 2 again. If the information matches at this point, go to step 6. If the information does not match, then set the sectors per track in the Master Boot Record to the number of sectors per track currently set in CMOS, set the starting head to 1, starting sector to 1, and starting cylinder to 0, and write the information to the drive.

Step Six: Verify the Master Boot Sector information

Display the Volume Boot Sector and use the values for heads and sectors per track (on the right half of the screen) to perform step 2 again.

If the values match, then the volume boot sector is probably okay. If any values in the Master Boot Record do not match the table to the right, reset the values to match the values in the table, and write to the drive.

If the values still do not match, both the Master Boot Record and the Volume Boot Record are probably corrupt. At this point, e-mail Technical Support for help in this situation. Future articles will provide more insight into the repair procedure.

Step Seven: Check the FATs

Check to see if the first FAT starts on the sector just beyond the volume boot sector. Use the find feature in the Fixed Disk Editor to search for F8 FF FF in the first three bytes of each sector. The first occurrence should be on sector two of head one. Continue to search until the second FAT is found, indicated by the second occurrence of F8 FF FF. Note the location of the cylinder, head and sector of the second FAT.

Based on the start of the second FAT, and the start of the first FAT, calculate how many sectors are in the first FAT. If necessary, read each sector starting at the first sector of the first FAT, keeping a count of the sectors that have been read until F8 FF FF is seen in the upper left of the HEX display, which would indicate the start of the second FAT. After calculating the sectors per FAT, compare this value to the value in the volume boot sector. If the values match, the drive should be accessible through DOS at this point.

Step Eight: Attempt to access the drive

Boot to a DOS-bootable floppy diskette and attempt to access the drive. If the root directory and sub-directories on the hard drive are readable at this point, then attempt to boot to the drive. If the drive boots at this point, the problem has been corrected. If the drive is still not bootable, e-mail the Micro 2000 Technical Support department for help.

Disclaimer - The Micro 2000 Tech Tip is a free service providing information only. While we use reasonable care to see that this information is correct, we do not guarantee it for accuracy, completeness or fitness for a particular purpose. Micro 2000, Inc. shall not be liable for damages of any kind in connection with the use or misuse of this information.

Micro 2000 Inc has been helping to solve the day-to-day challenges that IT departments face in order to keep their businesses operational as well as profitable for over 14 years. The company's primary goal is to put the customer first - through feature-rich, simple-to-use IT tools that can help IT administrators manage their jobs more effectively.

For more advice and free articles be sure to visit: http://www.micro2000.co.uk

---

The Importance Of Current Sense Resistor In Switch Mode Power Supply

Current sense resistor is usually located in the switch mode power supply section. Newer version of monitor-the b+ (boost) circuit also have this current sense resistor. If you repair electronic equipment especially the... Read More

What Everybody Should Know About An Inkjet Printer: The One-Year Cost Of Printing

You can purchase an inkjet printer for as little as $39. With a rebate, it may even be less. Not many people would argue about the good deal they got when they purchased... Read More

Rackmount Computer Keyboards

The other piece of vital equipment to accompany the rack mount computers and the monitors are the rack mount computer keyboards. Rackmount computer keyboards are built with durability and reliability in mind.Most keyboards... Read More

Computer Hardware Preventive Maintenance Software

Computers often break down at the worst of all times. These problems can be averted, or at least minimized with preventive maintenance. Several methods of keeping computer hardware in good working order deal... Read More

A Look Inside The Elusive Inkjet Industry

The Inkjet printer industry is booming. Office supply companies report they make more money on ink sales alone than on printer sales overall. Due to increasing ink sales, many inkjet manufacturers have introduced... Read More

RAID Disk Recovery

RAID is short for Redundant Array of Independent (or Inexpensive) Disks, a category of disk drives that employ two or more drives in combination for fault tolerance and performance. RAID disk drives are... Read More

Adding USB 2.0

The process of adding USB 2.0 ports took no time and the backup system is mighty fast. If you add USB 2.0 ports with a PCI port card, then you'll still have your... Read More

A Review of Refurbished HP Laptops

HP refurbished laptops can be found on their website hpshopping.com. Just enter "refurbished laptop" into their search field and browse through the current selections. (Note that Hewlett-Packard also owns and distributes Compaq computers.)... Read More

Pixel Disruption To Cause Nausea From User of Computer Screen

As we study the issues associated with teaching kids in the classroom we find that fluorescent lighting can plague the learning abilities. A slight flicker from such a light can cause disruption in... Read More

Got The Message that You Need New Ink Cartridges?

We all know what it is like when that message flashes on the computer screen as you are printing off an important document. Your ink cartridge is low, replace soon! But, do you... Read More

High Definition DVD

High definition DVD, also known as HD-DVD (which actually stands for High Density DVD), is one of two competing high definition storage format - the other being Blu-ray.The need for a... Read More

Ten Things Everyone Should Know about Ordering an Inkjet Cartridge Online

It is true. You can save a lot of time and money by ordering your next inkjet cartridge online. Today, there are many reputable online printer ink merchants. They sell quality ink cartridges... Read More

Laptop Computer Extras for the Mobile Traveler

A laptop computer certainly provides you with an unprecedented level of freedom and mobility away from the office. However there are a few extras you might want to bring along on your laptop... Read More

Best DVDs for Your Personal DVD Player

When bought personal DVD player, the very next thing to do is purchasing an important DVDs collection with your favourite movies, documentaries, shows, cartoons. Here are few hints before buying.Have you just bought... Read More

Power and Your PC

The power coming into a computer is the most critical component, and it may be one of the most overlooked. It is just taken for granted that it will always be there and... Read More

At War With The Internet

When it comes to sales of technology products over the Internet, there are now two factors that potential buyers must consider as possibly 'too good to be true'. In the past, there was... Read More

Where Can I Find The Best Case Mods Online and Save Money?

Are you captivated by the stunning Case Mods you've seen online but shell shocked at some of the prices.What is a case mod, some of you may ask? Have you every wanted to... Read More

Blu-ray: A Primer

Blu-ray is an optical disc format which is set to rival HD-DVDin the race to be the de-facto standard storage medium for HDTV. The HD-DVD vs Blu-ray battle resembles that between... Read More

The Top 10 Must-Have Laptop Accessories

You've laid out good money for your laptop computer, but you're not done spending just yet.There are a few more laptop accessories you may want to consider to make the package complete.1: Laptop... Read More

How to Add or Remove an IDE ROM drive

CD ROMS - If you're adding or removing an internal cd-rom, dvd-rom, or just about any internal ROM that has an opening CD door, read on. Almost all IDE devices such as CD-ROM,... Read More

Ceramic Disc Capacitor-How to Accurately Test It

The last article I mentioned about electrolytic capacitor breakdown when under load. In this article I will talk about the high voltage resin coated ceramic disc capacitor. In computer monitor, it is frequent... Read More

Testing Flyback Transformer - How to Test and When to Replace It

Nowadays, more and more monitor comes in with flyback transformers problems. Testing flyback transformers arenot difficult if you carefully follow the instruction. In many cases, the flyback transformer can become short circuit after... Read More

Getting to Know Inkjet Printers

Inkjet printers were born in the 1980s, replacing the popular dot matrix printer. Inkjet printers drop droplets of ink onto printer paper to produce text and images. The drops of ink are actually... Read More

Preventing Tape Drive Failure

Contrary to popular belief, tape drives are generally robust and reliable. However, there are three common mistakes that people make that dramatically increase the probability of tape drive failure.Firstly, it is not well... Read More

Flyback Transformer-How to Locate the ABL Line

Whenever there is a complaint about monitor contrast problem I will check on the flyback transformer ABL (automatic blanking limiter) circuit. Sometimes a weak picture tube might caused contrast problem. If the picture... Read More

Unclogging Epson Print Heads

Tools needed:1 - 10cc Injector1 - 4" - 5" of fish tank air line tubing (Wal*Mart fish department) Windex (No Drip works best)We are going to flush the print head out with the... Read More

Learn to Find Cheap Laptop Computers on the Internet

Cheap laptop computers are coming to a store near you. In fact, there are many there already. That's because, like any newfangled electronics device, laptop computers were once the cream of the computer... Read More

Expert Guide to DVD Camcorders

Thinking about a mini DVD camcorder? You're not alone, it's a rapidly growing sector of the camcorder market, with Hitachi, Sony and Panasonic all making more than one mini dvd camcorder.These camcorders differ... Read More

Used Laptop Computer: Your Quick Purchase Inspection Guide ? Part 4

Used laptop computers are everywhere these days. How can you sift through the mass of available used laptop computers to narrow your search down to the right laptop for you? This fourth and... Read More